To upgrade from ACS 5.1 to 5.3, see the Installation and Upgrade Guide for Cisco Secure Access Control System 5.3. Use Path 3 to upgrade from ACS 5.3 to ACS 5.6. Step 5 The ACS 5.6 patch install displays the md5 and sha256 checksum. Compare it with the value displayed on Cisco.com at the download site. Step 2 Install ACS in a Cisco SNS. Hi All, I hope some one can help out with this problem. I have an ACS 5.1 with the following S/W load Cisco Application Deployment Engine OS Release: 1.2 ADE-OS Build Version: 1.2.0.146 ADE-OS System Architecture: i386 Cisco ACS VERSION INFORMATION ----------------------------- Version: 5.1.0.44 Internal Build ID: B.2347 I have downloaded 5-1-0-44-3.tar.gpg, 5-1-0-44-4.tar.gpg and 5-1-0-44-5.tar.gpg to a local repository on the ACS but when ever I try and run the patch upgrade process acs patch install 5-1-0-44-5.tar.gpg repository repository_name I get the following error output. Chmod: cannot access `*.sh': No such file or directory Invalid patch '5-1-0-44-5.tar.gpg' - missing install.sh% Error: Failure to open / validate the patch I have moved the 5-1-0-44-5.tar.gpg to a linux box and have tried to dencrypt the file using gpg -d 5-1-0-44-5.tar.gpg but it then prompts for apass phrase, I tried a few guesses but I could not decrypt it. So what part of the upgrade process am I missing, or do I need to install some sort of pass phrase so that the ACS can properly decrypt the patch files. I have tried this with patch 3, 4 and 5. Do I need to start off at pathch 1? Thanks Cefyn Arch. Helloz, Form where did you download the patch. I would suggest you to download from cisco.comif you didn't download before. No, You can directly apply the patch 5. ![]() The command you are running to apply the patch is correct. I would like you to check the few things 1. Are you using TFTP? ![]() IF yes, then switch to FTP and then try. Before you apply the patch, make sure you can see the file under the repository. Show repository if you can see patch 5 under the repository then you are good to go. HTH Jatin ~Do rate helpful posts. Helloz, Form where did you download the patch. I would suggest you to download from cisco.comif you didn't download before. No, You can directly apply the patch 5. The command you are running to apply the patch is correct. I would like you to check the few things 1. Are you using TFTP? IF yes, then switch to FTP and then try. Before you apply the patch, make sure you can see the file under the repository. Show repository if you can see patch 5 under the repository then you are good to go. Adagio cellos. HTH Jatin ~Do rate helpful posts. Hi I just installed ACS 5.1 from the ISO into our ESX vsphere server. Vlc media player 64 bit. Install went great and even saw applications get installed. When system rebooted, I logged in successfully. Framingham risk score calculator pdf files. Tried to check status on application acs, but nothing. Ran: show application status acs result: Error finding status information for the application ran: application start acs result: Application failed to start Hmm. Did I miss a step somewhere? I can ping the system remotely, just doesn't look like the application is running. Hi i had that problem but it is solved now. Before i used linux but it was not working with my ACS file than i used microsoft server 2012 guest operating system i was able to ping ACS ip with my laptop,but while in vmware i can not ping to laptop loopback ip address,but even i was able to see gui through web browser first check sh application status acs and you should wait for few minutes to get it initialize if it does not show anything than might be problem with that ACS file or you can uninstall that it and boot it again.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |